MACHINE SHOP PRICES

Automotive Machine Shop Prices for Jet Engine Cleaning, HEAD PORTING, VALVE JOBS, 3 Angle High Performance Valve Jobs, Resurface Heads, Resurface Blocks, Crankshaft Regrinding, magnaflux, Bore Block and Hone, Ridge Ream and Hone, Rod Reconditioning, Foreign Valve Jobs, Flywheel Turning, Turn Rotors and Drums & Yes We're in Snellville Ga.

Jet Engine Cleaning

Crankshaft ............... 16.00

Intake Manifold ....... 20.00

Engine Block .......... 50.00

Oil Pan ...................... 8.00

Cast Iron Head ....... 50.00

Aluminum Head .... 50.00

Valve Cover ............ 5.00

Timing Cover .......... 5.00

Complete Engine 125.00

Rods ...................... 10.00

Engine Bolts ......... 10.00

HEAD DEPARTMENT

HEAD PORTING

A PAIR V8 HEADS ..... 500.00

A PAIR V6 HEADS ..... 475.00

A L6 HEAD ................. 475.00

A 4 cyl. HEAD ............ 300.00

Enlarge Valve Bowls 200.00

Extract Studs . torch 8.00 (ea.)

Install Helicoil ............. 11.00 (ea.)

Drill & Retap ................ 15.00 (ea.)

Install Press Stud ......... 7.00

Remove Stud and Install
Screw In Rocker Stud 12.00 a piece

INSTALL FIRST

VALVE GUIDE OR SEAT...... 15.00

EACH ADDITIONAL .............. 8.00

Press Small Bearing ..................... 10.00

Press Hub Bearing ..................... 45.00

Press Front Wheel Bearing 45.00

Press Axle Bearing 45.00

POLISH Valve Springs, Retainers 30.00 (NEW Service)

Install Cams and Adjust Clearances 90.00

VALVE JOBS USA
3 cyl 2 Valve .......... 80.00

4 cyl 8N Ford FlatHead Block
& Ajust Valves ...... 100.00

4 cyl 2 Valve .......... 85.00

L6 & V6 ..................... 95.00

V8 ............................... 99.00 (ea.)

Posted 2001 May 14, Seems Like No one on the Web Knows What a High Performance 3 Angle Valve Job Is
Surprise Surprise the High Performance 3 Angle Valve Job Has ( 5 ) Angles
They Are 15 deg, 30 deg, 45 deg, 60 deg, 70 deg.

3 Angle High Performance Valve Jobs For V8 .. 270.00

3 cyl diesel tractor ........... 120.00

2 cyl John Deer tractor ......... 70.00

2.3 Ford w/Bearing Installed 130.00

(Quad 4 .........100.00) w/cam.. 130.00

Knurl Guides ............................... 3.00 (ea.)

Grind Valves ............................. 1.00 (ea.)

Pressure Test Aluminum Head .. 45.00

Pressure Test Cast Iron Head ..... 45.00

Resurface Heads

2 cyl ................................ 30.00

3 cyl ................................ 30.00

4 cyl ................................ 20.00

5 cyl ................................ 35.00

6 cyl ................................ 35.00

8 cyl ................................ 40.00

V8 DIESEL .................... 100.00

Check Head For Warpage ........ 8.00

Mill Exhaust manifold ... 30.00

Resurface Blocks

Mill 2 Cyl Block John Deer Tractor 80.00

Mill 3 Cyl Block Ford Tractor .......... 80.00

Mill 4 Cyl Block ................................ 55.00

Mill 5 Cyl Block ................................ 60.00

Mill 6 Cyl Block ................................ 65.00

Mill V6 or 8 Cyl Block ...................... 75.00
Crankshaft Regrinding

2 CYL John Deer .......gas-125.00 - diesel 175.00

3 CYL John Deer...... gas-150.00 - diesel 275.00

4 CYL ........................... 125.00

5 CYL ........................... 175.00

6 CYL ........................... 135.00

8 CYL ......................... 165.00

Weld Journal ........ 30.00 ea.

Clean and Polish ........ 45.00

MIC Crankshaft ............. 7.50

Check for Straightness 8.00

Polish Crankshaft ....... 35.00

(finding cracks)
Head 4 cyl ............... 20.00

Head long 6 cyl ....... 20.00

Head V6 .................. 20.00

Head V8 .................. 20.00

Block ....................... 45.00

Bore Block and Hone

1 cyl ............................................. 35.00

2 cyl John Deer .......................... 75.00

3 cyl Ford Tractor ....................... 75.00

3 cyl ............................................. 70.00

4 cyl Ford Tractor ....................... 75.00

4 cyl ............................................. 75.00

5 cyl Ford Tractor ....................... 80.00

6 cyl ............................................. 85.00

8 cyl ........................................... 110.00

Mic Cylinder ............................... 10.00

Check Main Saddles .................. 20.00

Align Hone Block 3 to 5 Mains 110.00

Each Additional Main ................. 18.00

Ridge Ream and Hone

Hone 4 Cylinder Block ...................... 40.00

Hone 6 Cylinder Block ...................... 50.00

Hone 8 Cylinder Block ...................... 60.00

Cam Bearing Installed ...................... 20.00

Cam Bearing Removed .................... 20.00

Install Sleeve ..................................... 80.00

EACH ADDITIONAL ........................... 55.00

(Following is for building the block - if you have your own parts)

Build 4 CYL Short Block ................. 138.00 (Labor Only)

Build 4 CYL Complete .................... 220.00 (Labor Only)

Build 6 CYL Short Block ................. 165.00 (Labor Only)

Build 6 CYL Complete .................... 245.00 (Labor Only)

Build 8 CYL Short Block ................. 300.00 (Labor Only)

Build 8 CYL Complete .................... 350.00 (Labor Only)

Build High Performance Short Block 395.00 (Labor Only)

Build High Per. Block Complete 450.00 (Labor Only)

Install Freeze Plugs ............. 20.00

Remove oil Gallery Plugs ..... 1.00 (ea.)

Cut Drive Shaft ..................... 35.00 a Cut

Cut Shorten Drive Shaft ...... 65.00

Install Flywheel Ring Gear ...... 35.00

Rod Reconditioning

Press on Rod or Piston.... 5.00 (ea.)

Set ..................................... 4.00 (ea.)

Replace Pin Bushing ..... 10.00 (ea.)

Set ..................................... 8.00 (ea.)

Recondition Rod ............ 18.00 (ea.)

Set ................................... 15.00 (ea.)

Check Rod Sizing ............ 5.00 (ea.)

Balance ROD .................. 22.00 (ea.)

Balance PISTON ............ 22.00 (ea.)

Foreign Valve Jobs

3 cyl 2 valves per cyl sohc ........ 100.00

3 cyl 3 valves per cyl sohc ........ 110.00

3 cyl 4 valves per cyl sohc ........ 135.00

4 cyl 2 valves per cyl sohc ........ 120.00

4 cyl 3 valves per cyl sohc ........ 130.00

4 cyl 4 valves per cyl sohc ........ 165.00

5 cyl 2 valves per cyl sohc ........ 150.00

5 cyl 3 valves per cyl sohc ........ 180.00

5 cyl 4 valves per cyl sohc ........ 200.00

6 cyl 2 valves per cyl sohc ........ 160.00

6 cyl 3 valves per cyl sohc ........ 180.00

6 cyl 4 valves per cyl sohc ........ 225.00

3 cyl 4 valves per cyl DOHC ...... 180.00

4 cyl 4 valves per cyl DOHC ...... 225.00

5 cyl 4 valves per cyl DOHC ...... 250.00

6 cyl 4 valves per cyl DOHC ...... 300.00

8 cyl DIESEL VALVE JOB .......... 200.00

Flywheel Turning

(Turn Flywheel ............................. 30.00

2 Step ............................................ 40.00

Heavy Duty ..................................... 70.00

Turn Rotors and Drums

Turn Rotors ........... 9.00

Heavy Duty ........... 15.00

Turn Drums ........... 9.00

Heavy Duty ........... 15.00

FOR ENGINE PRICES ON SHORT & LONG BLOCK UNITS, GIVE US A CALL or EMAIL US BELOW.
SHOP 678-906-3231

Email: support@aacncclub.com

welding 45.00 hour / machine work 30.00 hour

owner stan cruce
prices subject to change without notice

custom remanufactured long blocks with a 12 month or 12,000 mile warranty

MAP TO FIND CRUCE MOTOR REBUILDING: CLICK HERE

Beware of the Automotive Machine Shops That Do not Have a Written Price List of Services
Automotive Machine Shop Prices for Jet Engine Cleaning, HEAD PORTING, VALVE JOBS, 3 Angle High Performance Valve Jobs, Resurface Heads, Resurface Blocks, Crankshaft Regrinding, magnaflux, Bore Block and Hone, Ridge Ream and Hone, Rod Reconditioning, Foreign Valve Jobs, Flywheel Turning, Turn Rotors and Drums & Yes We're in Snellville Ga.

Cruce Motor Rebuilding is not responsible for items left over 30 days.
Cruce Motor Rebuilding is not responsible for items shipped to or from Cruce Motor Rebuilding
(including transport or wrecker services)

Posted 2001 May 14, Seems Like No one on the Web Knows What a High Performance 3 Angle Valve Job Is Surprise Surprise the High Performance 3 Angle Valve Job Has ( 5 ) Angles They Are 15 deg, 30 deg, 45 deg, 60 deg, 70 deg.

FOR ENGINE PRICES ON SHORT & LONG BLOCK UNITS, GIVE US A CALL or EMAIL US BELOW. SHOP 678-906-3231

welding 45.00 hour / machine work 30.00 hour

owner stan cruceprices subject to change without notice

custom remanufactured long blocks with a 12 month or 12,000 mile warranty

Posted 2001 May 14, Seems Like No one on the Web Knows What a High Performance 3 Angle Valve Job Is
Surprise Surprise the High Performance 3 Angle Valve Job Has ( 5 ) Angles
They Are 15 deg, 30 deg, 45 deg, 60 deg, 70 deg.

FOR ENGINE PRICES ON SHORT & LONG BLOCK UNITS, GIVE US A CALL or EMAIL US BELOW.
SHOP 678-906-3231

owner stan cruce
prices subject to change without notice